صور الصفحة
PDF
النشر الإلكتروني

read a description of it before the Institute of Civil Engineers in 1846. In this engine two strong air-tight vessels are connected with the opposite ends of a cylinder, in which a piston works in the usual manner. About four-fifths of the interior space in these vessels is occupied by two similar air-vessels, or plungers, suspended to the opposite extremities of a beam, and capable of being alternately moved up and down to the extent of the remaining fifth. By the motion of these interior vessels the air to be operated upon is moved from one end of the exterior vessel to the other; and as one end is kept at a high temperature, and the other as cold as possible, when the air is brought to the hot end it becomes heated, and has its pressure increased, whereas its heat and pressure are diminished when it is forced to the cold end. Now, as the interior vessels necessarily move in opposite directions, it follows that the pressure of the enclosed air in the one vessel is increased, while that of the other is diminished; a difference of pressure is produced on opposite sides of the piston, which is made to move from one end of the cylinder to the other. The piston is connected with a fly-wheel, and motion communicated in the usual way. A large bakery has been established on this principle at New York, the machinery being worked by the ascensive force of a current of air heated by the baking ovens. At a certain height within a lofty vertical shaft is a horizontal wheel, with wings or vanes attached at an angle of 10°; the ascending air causes this wheel to revolve horizontally; drums are fixed on the spindle of the wheel, and straps or bands from these drums drive the machinery for grinding the flour and kneading the dough.

Baron Von Rathen made trial of an air-locomotive on a common road, in 1848. It travelled from Putney College (where it was constructed) to Wandsworth, at the rate of 10 or 12 miles an hour., The air-reservoir (substitute for a steam boiler) had a capacity of 75 cubic feet; it was capable of being charged with air to a pressure of fifty atmospheres, by a 6-horse power engine.

An air-engine of peculiar construction was employed in 1851, in the Govan Colliery, near Glasgow, invented by Mr. Randolph. There were circumstances connected with the shape and arrangement of the shafts of the mine which rendered the supply of steam difficult; whereupon Mr. Randolph, acting on a suggestion made by Mr. David Elder, contrived the air-engine. He makes use of compressed air, supplied by a compressing steam-engine at the surface, and conveyed down by a pipe to work an engine at the top of the second shaft, in the manner of a non-condensing steam-engine; the discharged air being thrown into the workings to aid in the ventilation of the mine. The air-engine, supplied by the compressing apparatus, is employed for working the winding and pumping apparatus of the second shaft. The compressed air is conveyed to it through a cast-iron shaft 10 inches in diameter, carried down the main shaft. At a meeting of the Institution of Mechanical Engineers, in 1857, it was stated that this machine had been working admirably for six years, and had illustrated many points connected with the useful employment of air-engines.

There are certain forms of air-engines, especially Ericsson's, which will be better noticed under CALORIC ENGINE.

AIR-GUN. An instrument for projecting bullets, in which the

and simplest construction.

moving power is the rush of condensed air allowed to escape, instead | densing Syringe, as the two differ very slightly in their main principle of the formation of gases arising from the ignition of gunpowder. The air-gun and the common gun are therefore the same in principle. In the stock of the gun is a condensing syringe, the piston of which condenses air into a cavity, which has a valve opening inwards, just behind the bullet. The barrel is open, and the bullet (which should just fit it) is inserted in the usual way. The trigger opens the valve behind the bullet, and permits the rush of the condensed air, which propels the bullet. The moment the finger is withdrawn from the trigger, the air closes the valve, and remains, somewhat less condensed than before, for the next discharge.

The same principle has been variously applied. In the magazine air-gun, there is a reservoir of bullets, in a channel under the barrel, one of which is turned in by a cylindrical cock pierced by a tube, which in one position is a continuation of the reservoir of bullets, and in another, of the barrel. Thus, by turning the gun upside down and turning the cock, a bullet falls into it from the reservoir, which, on re-turning the cock, is of course in the barrel. This is a very primitive application of the now famous principle of the Revolver, or revolving pistol. In some air-guns, the cavity containing the condensed air is a hollow copper ball, which can be screwed on to the gun after condensation. The air-cane is so called because it is usually in the form of a walking-stick. The handle contains the condensed air, and can be unscrewed and filled by a separate condensing syringe. There is some mention of an instrument similar in principle to the air-gun among the ancients; and it is said that Ctesibius, a celebrated mechanical philosopher, who lived, B. c. 120, at Alexandria, constructed an instrument, in which the air, by its elastic force, discharged an arrow from a tube. (Montucla, Histoire des Mathématiques,' vol. i. p. 267.) The invention, such as we have described it, is ascribed to Marin, a native of Lisieux, in France, who is said to have presented an air-gun to Henry IV. Shaw's air-gun, patented in 1849, combines an endless band of vulcanised india-rubber with an air-exhausting apparatus. The elasticity is so applied as to compress the air by a single stroke of a syringe or air-pump, the moment before the discharge. The operation performed by the sportsman, to bring the apparatus into a charged condition, is very similar to that adopted in the use of the cross-bow.

Down to the present period, however, the air-gun, in all its forms, has been little other than a mere toy. No power, but only an adaptation of power, is gained by its use; for the condensation of the air itself requires force. The air-gun has never been used in war, on account of its expense, and the force which must be employed to condense the air. The steam-gun, exhibited in London a few years ago, exemplified a much more forcible agent than air for the propulsion of bullets; but nothing has hitherto been accomplished to render that mechanism practically available, although suggestions to that effect were made during the Russian war of 1854-5.

Fig. 1.

Glass
Receiver.

Fig. 2.

Above we have the sections of the simplest forms of an exhausting and of a condensing syringe. Both consist of a brass tube or cylinder, closed at one end, excepting an orifice to which a valve or lid is attached. A piston, with a rod and handle, enters at the other end, and can be moved up and down the tube. The piston is not entirely closed, but has a valve opening the same way as the other valve. Both are attached to vessels the air of which is to be rarefied or condensed. In fig. 1, or the exhausting syringe, both valves open upwards, or let air only out of the vessel and the piston: in fig. 2, or the condensing syringe, both open downwards, or let air only into the vessel and through the piston.

Let the whole contents of each vessel be, for example, six times that of the tube of the syringe, and let both pistons be pushed down. We first take the exhausting syringe. The instant the piston begins to rise, there is no air between A and B; the valve A is kept shut by the pressure of the exterior air, while the air in the vessel, pressing on B from underneath at the rate of about fifteen pounds to the square inch, raises it, and the air in the vessel is thus distributed between the vessel and the tube. If we call the tube one measure, the vessel is six measures; so that the air which occupied six measures now occupies seven, or is only six-sevenths of its former density. When the piston is returned again, the air in the tube is compressed, but cannot return AIR-PUMP. A philosophical instrument for removing the air out into the vessel, because B does not open inwards. By the time the of a vessel. We shall also include under this head the apparatus for piston has returned through one-seventh of its descent, the equilibrium forcing more air into a vessel, better known by the name of the Con-between the air in the tube and the external air will be re-established;

and by the time the piston has descended so much farther that the additional elastic force acquired from compression will suffice to lift the valve A, the latter will open, and the air will rush out. This continues until the piston has quite returned to B. That is to say, after every stroke of the piston, the air in the vessel has only six-sevenths of the density which it had before the stroke, since the air contained in six measures is expanded into seven by the rise of the piston. Therefore, at the end of the second stroke the density is of, or 3, that is, 36 measures of common air would weigh as much as 49 of the air we have now got inside the vessel. At the end of the third stroke the density is of, or 18. Without going farther, suffice it to say, that at the end of the twentieth stroke, the density of the rarefied air is about; and at the end of 100 strokes, it would take about five million of measures of the rarefied air to weigh as much as one of common air. But long before this time a limit would be put to the exhaustion, in the present state of the apparatus. The air in the vessel cannot escape into the tube unless it has force sufficient to lift up the valve B; which after a certain number of strokes will not be the case, for the elastic force of the air diminishes in the same proportion as its density, being at first fifteen pounds to the square inch; so that by the time the density is reduced to the valve, if it present a surface of one square inch, will not rise, if it be so heavy as half an ounce. Let us, then, suppose в to be fastened to the piston by a loose string, so long that it becomes tightened just before the piston reaches its greatest height. The string will then open the valve, and the rarefaction will take place as usual.

The condensing instrument will now be easily understood. Let the piston be raised, the valves will then be open; but the moment the piston begins to descend, the rush of air outwards will shut c, and the whole of the air in the tube will be forced into the vessel, which admits it, since D opens inwards. If this be done quickly, so that hardly any air escapes, seven measures of air, after the stroke, will occupy the space filled by six measures before it, so that the density of the air in the vessel will be ; or six measures of condensed air will weigh as much as seven of common air. When the piston returns, air rushes in through c, and presses the valve D, which nevertheless, unless made too heavy, does not open, because it is pressed with a greater force from within. In every succeeding stroke an additional measure of common air is added to the stock already contained in the vessel. At the end of the second stroke the density is 8, at the end of the third, and so on. Every succeeding stroke will be more difficult,

exhausting syringe takes place in geometrical progression. It would take 30,000,000 of strokes, all but one, to produce a condensation, the corresponding rarefaction to which is gained in a hundred. It is needless to say, that no materials that we could put together would bear such a pressure, and no force that we could exert would create it. The exhausting syringe, as above described, is, in principle, the common air-pump. We shall now proceed to describe Cuthbertson's air-pump, containing the most recent material improvements. The circular plate or table at the top is of metal or of glass ground to a perfect plane surface, on which is placed an inverted glass jar, from which the air is to be exhausted, called the receiver, the bottom of which is also carefully ground: so that if the plate be slightly smeared with grease and the receiver placed upon it, the junction of the two is air-tight. The hole in the middle of the plate is the end of a tube, which extends vertically downwards, until, curving at the bottom, it passes through the front beam below the barrels, with the interior of each of which it communicates. These barrels are exhausting syringes, the construction of which will presently be more particularly described: they are worked by rack-work, communicating with a cogwheel and handles, space for the racks to play being cut in the upper wood-work of the apparatus. On the left are the gauges for ascertaining the degree of exhaustion obtained, and at A is a place for a PEAR-GAUGE. See also SYPHON-GAUGE, as we shall here only describe the most common, the barometer-gauge. The box attached to the under beam on the left contains mercury, out of which rises a tube and a graduated scale, as in the barometer. This tube passes through the higher wood-work, and also ends in the orifice which is in the middle of the plate, so that the communication being free, the air in the receiver, and that in the tube above the mercury, are in the same

[graphic][merged small][merged small]

for the air contained between C and D in the descent of the piston, will not force D open until it is more compressed than the air within the vessel. Also the condensation increases only in arith- state. Hence as the air is rarefied, the external air will force some metical progression, while the corresponding rarefaction in the mercury up the tube, and the height to which it has risen will show

the degree of rarefaction. For example, suppose the common barometer to be 30 inches high, while the barometer-gauge of the air-pump stands at 20 inches. If the vacuum were complete, the barometergauge would be a common barometer, and would stand at 30 inches: but as it stands only at 20 inches, the pressure of the air in the receiver is equivalent to 10 inches of mercury, or one-third of that of the exterior air. Therefore the density of the air in the receiver is one-third of that of the exterior air, or two-thirds of the air have been removed.

The preceding cut shows a section of the piston rod, as well as of the barrel. The tube m comes from the receiver, and air can be admitted by it into the barrel, when the rod gg is raised. The rod gg passes into the piston-rod (which is hollow), and works stiffly in it, being however unconnected with it except by friction. This rod consists of two parts, above and below L, the latter of which is not thick enough to fill the orifice in which it plays. But when the piston descends, the conical juncture of the thicker and thinner parts is brought upon this orifice, and shuts it close. After this, and during the rest of the descent, the hollow piston-rod slides downwards upon the rod gg. As soon as the piston begins to ascend, the rod gg is raised with it, owing to the friction, so far as the nut o will let it rise, after which the piston-rod slides up gg. We have here the lower valve of the

exhausting syringe, shut during the descent of the piston, open during the ascent, and not opened by the force of the air from underneath, so that the functions of the string which we supposed in our first exemplification are performed. A little higher up the barrel we find the piston, as better shown in the adjoining figure. The external part is a partial piston not connected with the piston-rod, but fitting closely to the barrel. The piston-rod, when rising, fits this exactly, renders it airtight, and causes it also to rise. But when the piston-rod is descending, it will not cause the descent of the exterior, and, as we have called it, partial, piston, until the projecting shoulders aa (in the figure) come upon it; and, as these shoulders do not go all the way round, the piston in descending is not air-tight. This apparatus supplies the place of the upper valve, being air-tight in the ascent, but not so in the descent. Looking above the piston, we find that its rod works in metal shoulders, the interval between which is occupied by stiff leathers. The space above the leathers opposite to a is filled with oil, which is communicated slowly to the leathers, and also to the barrel beneath. From the latter, however, it is immediately expelled by the rise of the piston, which forces it, as well as the air in the barrel, through the channel aa. The oil and the air then force up the rod in the cavity R, which rod, working in collars, answers the purpose of a valve. The oil is there lodged, until it is collected in sufficient quantity to flow again into the reservoir at T. The air escapes into the exterior atmosphere. Having shown that we have here an under valve shut during the descent, and open during the ascent, with an upper valve open during the descent and shut during the ascent, we need not repeat the manner in which the rarefaction is produced. We have only further to notice, that a branch from the main tube which enters the receiver is carried through the under wood-work in front, and emerges at B. It is here stopped by a screw; but when the operator desires to restore the air under the receiver, he opens this screw, upon which the communication between the exterior atmosphere and the receiver is restored, and the air rushes in. In the perspective figure, a cross bar, in which the upper parts of the barrels are inclosed to strengthen them in their position, is omitted for the sake of clearness.

We give in the following figure a representation of a more portable and less expensive species of air-pump, which, after what we have said, will need no description.

The small plate behind the receiver is for another small receiver, in which a gauge is placed. This guage is nothing more than a common barometer, which falls with the diminution of pressure from the air in the receiver, in the same way as the common barometer when the pressure of the exterior air is lessened by a change of weather.

The following experiments are among the most common of those shown with the air-pump :

1. If the receiver be open at both ends, and the upper orifice be stopped by the hand,-on exhaustion the pressure of the exterior air will prevent the removal of the hand. If a piece of bladder be tied tightly over the orifice, as the exhaustion proceeds the bladder will be pressed inwards, and will finally burst with a loud report. The pressure of the air is also proved by the experiment of the hemispheres, described in the article AIR.

[merged small][graphic]

soon as the exhaustion begins. A shrivelled apple will be restored to apparent freshness by the expansion of the air which it contains, but will resume its original appearance when the air is allowed to return. 4. The elasticity of air may be shown by placing a bladder under the receiver, not distended, and the mouth of which is tied up. On exhausting the receiver, the air contained in the bladder will expand it more and more, as more of the pressure from the exterior is removed; and the bladder will finally burst from the interior pressure. If a hole be made in the smaller end of an egg, and the egg be then placed in a wine-glass with this end down under the receiver, the small bubble of air which is always found in the larger end, will, by its expansion, force out the contents of the egg. On re-admitting the air, the contents of the egg will be forced back into the shell.

The

The first vacuum was made by Torricelli [TORRICELLI, in BIOG. Div.; BAROMETER], but the first air-pump was constructed by Otto von Guericke, who exhibited it publicly at the Imperial Diet of Ratisbon in 1654. It was an exhausting syringe, attached underneath to a spherical glass receiver, and worked somewhat like a common pump. syringe was entirely immersed in water to render it air-tight. Shortly afterwards, Boyle constructed an air-pump in which the syringe was so far improved that the water could be dispensed with. He also first applied rack-work to the syringe. The second syringe and the barometer-gauge were afterwards added by Hawksbee, and several minor improvements were made by Gravesande and Smeaton. All the alterations which have been made since the time of the invention, however important, relate to the mechanism only, and not to the principle on which the pump acts.

In the Great Exhibition of 1851, among the instruments exhibited in Class X., the best air-pump was by Mr. Newman. It has a groundglass plate, and is furnished with two pumps with metal valves, on one of which are two barrels, open at the top. By this arrangement the receiver may be quickly exhausted to 0.4 inch or 0.5 inch. The other pump has a single barrel, with an oil-cistern at the upper part, and the air is lifted through a valve at the bottom of this cistern. "If anything re-enters the barrel it can only be oil, which is brought out with the air at the next up-stroke of the piston. The piston has a metal valve; but the opening of this valve is not necessary to the continuation of the exhaustion, as the piston at its lowest point passes below the aperture leading to the receiver. This construction of air-pump exhausts more thoroughly than any yet known." (Jury Report.') In some experiments which were tried with this pump, the reading of the barometer at the time was 30-08 inches, while the gauge of the pump stood at 30-06 inches.

A pump exhibited by Messrs. Watkins and Hill, on a plan suggested by Mr. Grove, has oil-silk valves, and is so constructed as to leave the least possible residue of air in the valve after each stroke of the piston. "The piston is solid, without a valve, and the shape of its lower part is an obtuse cone. Part of this cone rises at the top of each stroke above the aperture leading to the receiver; and the air which has entered the barrel is, by the down-stroke, forced through a valve at the apex of the hollow cone terminating the lower end of the barrel, to which the lower end of the piston fits very accurately. The pistonrods pass through air-tight leather collars in the tops of the barrels. This pump exhausted the air till the elastic force was only 0.05 inch of mercury."

Mr. Siemen's air-pump was exhibited by Knight and Sons. "It consists of two cylinders of different diameters, the smaller one placed

below the larger, and separated from it by a plate forming the bottom of the upper and the top of the lower cylinder. A piston-rod, common to both cylinders, passes through a stuffing-box in the plate, attached to which are two valved pistons, working in their respective cylinders. The advantage of this construction is, that the pressure of the external air on the oiled silk valve of the larger cylinder is taken off by the vacuum formed in the smaller one, and in consequence no greater resistance is offered by the valve than that arising from its adhesion and tension. The exhaustion of this pump is very rapid, and in the trial amounted to 0.24 inch of mercury." The motion of the pistons is effected by means of a short crank with a jointed connecting-rod, converting the circular motion given by the lever handle into a vertical one, which is maintained by means of a cross-head with rollers working between guides. This pump is more particularly described in Mr. Tomlinson's 'Rudimentary Treatise on Pneumatics.'

In the air-pump exhibited by Varley and Sons a new construction is adopted. "It is worked by a continuous rotatory motion of the handle, slide-valves being used to open and close the communication. On the piston arriving at one end to expel air from the barrel, it is followed by rarefied air from the receiver; the slide-valve closes upon the receiver and connects the two sides of the piston; the residual air expands into the larger space, becomes equally rarefied, and the subsequent motion of the valve separates these spaces, and connects the receiver with the closed end. The piston then returns to exhaust air into this end of the barrel and to expel it from the other, and thus continuous exhaustion is kept up; for, how rare soever the air becomes, it keeps flowing after the piston continually. The barrel is twice filled for every entire revolution of the handle. This pump has a single barrel with double action; it exhausts quickly, and the exhaustion was found to be 0.05 inch for a moment, but could not be maintained."

In the French department, the double-barrelled air-pump exhibited by M. Breton had, instead of valves, a glass plate sliding over apertures communicating with the receiver, and the pumps and the motion of this glass plate is produced by the mechanism which works the pump. "The approximate exhaustion is first made by the ordinary alternate action of the barrels. The system of communication is then changed by shifting round the glass plate, which serves as a valve during onefourth of a revolution, when the rarefied air is condensed in one barrel and sucked into the other, whence it is ultimately ejected through a valve of oiled silk very close to the piston." In the air-pump exhibited by M. Deleuil, the barrels were of glass, and the valves, after M. Babinet's plan, were opened by means of wires passing through the pistons. The opening of the valves is thus rendered independent of the elastic force of the air left in the receiver, and the degree of exhaustion must depend on the air remaining after the action of the piston. AISLE, or AILE (in Architecture), indirectly from the Latin word ala, a wing, through the French aile, which has the same signification. In French, this term is applied to the outlying and returning ends of a building, which we distinguish by its English equivalent, wing; such are the columned ends of the front of the British Museum. We apply the term aisle to the lateral divisions or passages of the interior of a church -those parts which lie between the flank walls and the piers, pillars, or columns, which flank the nave, or grand central division-when the structure is so arranged. Sometimes, but incorrectly, with reference to modern churches and chapels in this country, the mere passages or corridors which run between, and give access to the pews, are called aisles. Still more incorrectly, some writers, and even ecclesiastical writers, have called all the longitudinal divisions of the body of a church, aisles, thus including the nave under a designation which belongs only to its adjuncts and accessories.

The division of a church into what we term nave and aisles arose simply out of the difficuity which existed of spanning a great breadth with a roof without some intermediate support; and thus the greater Constantinian churches or basilicas of Rome were built with four rows of columns, forming five longitudinal divisions; that is, with two aisles on each side of the nave. This was imitated in subsequent structures, and the metropolitan churches of Milan and Paris were built in five divisions, or with four aisles, as they exist at the present time. That the custom of arranging the interiors of churches with aisles was continued in deference to ecclesiastical precedent, or at any rate long after the necessity for using the props which form them ceased architecturally, may be rendered clear by reference to the following fact. Most of our cathedrals and greater churches in this country are of later date than the roof of Westminster Hall, which, without intermediate support, spans a greater breadth than most of them can boast of; and yet they are, as a general rule, all divided into nave and aisles. In recent Gothic churches it is needless to add they are continued, even when, as in some of very small size, they are at once obstructive and costly.

In some English books, though perhaps in none of the present century, this term will be found written without the aisle. ALANINE (CH,NO,). When aldehyd-ammonia is acted on by hydrocyanic acid, and an excess of hydrochloric acid, a crystalline body, soluble in water, is formed, to which Strecker has given the name alanine. It crystallises in groups of prisms, which are insoluble in ether, nearly so in alcohol. Its solution has no effect upon test-papers. It sublimes at about 400°. It is homologous with glycocoll and leucine,

[blocks in formation]

ALARUM. It is curious to mark how much ingenuity has been displayed within the last few years in the invention of alarums, and how many patents have been taken out for the inventions. In most of these contrivances there is some little bit of mechanism which gives a shrill sound whenever attention is required to be directed to any subject with which the alarum is associated.

Without describing any of the older forms, we may glance at a few of the modern suggestions. The 'travellers' alarum' is a small brass box about 2 inches in diameter by 14 thick. It has hands which may be set to any hour to awaken a sleeper. Mr. Allen, in 1844, registered an alarum intended to prevent injury to boilers from the water falling below its proper level; it consists of a float within the boiler, a steam-whistle on the exterior, and a tube of connection; when the water is at a proper height in the boiler, the float is buoyed up, and the whistle is silent; but when the water, and with it the float, descend too low, a little valve in the tube opens, and a current of steam from the boiler ascends to the whistle, which immediately gives forth a shrill sound, thereby indicating that the water has sunk too low in the boiler.

An alarum patented by Mr. Doull, is a 'railway whistle,' so constructed as to yield several notes, capable of being combined into a code of signals. A chemical alarum' by Mr. Mowbray consists of a copper cylinder, with a whistle at the top; a piece of carbonate of lime and a little muriatic acid are put into the cylinder, by which carbonic acid gas is speedily generated; and this is forced by some kind of mechanism into the whistle, whenever a sound is required to be produced. A contrivance by Mr. Hoare, described before the Society of Arts, consists of a chain of rods extending from end to end of a railway train, and moving freely on joints; at the end of the chain, in the guard's carriage, is a crank which, when the rods rotate on their axes, comes in contact with a hammer, and causes it to strike a bell; the driver, or the passengers in any carriage, can give a slight rotatory motion to the rods, and thus signals may be communicated. Up to the present time, however, all kinds of railway train signals have been sadly neglected. See further on this subject under RAILWAY.

But the busiest contriver of alarums, perhaps, is Mr. Rutter, who has called to his aid the marvels of electricity. In a patent for several such contrivances, taken out by him in 1847, one variety is the 'Fire Alarm', a complicated apparatus intended for use in large buildings. A galvanic battery is placed in one room, the alarum in another, thermometers in every room, and copper wires to connect all these pieces of apparatus. If the temperature of any room be greatly raised, as by accidental fire the rising mercury in the thermometer comes in contact with a metallic wire, which sets the galvanic battery in action, and this again works the alarum-bell in the same way as an electro-telegraphic clock, but with an adjustment intended to show in which room the rise of tempe rature has occurred. A second variety, the Trespass Alarum,' depends for its action on the placing, near every door and window, of a tube containing mercury, open at the top; the opening or closing of the door or window brings a small wire into contact with the surface of the mercury, and this completes a galvanic connection with a battery in another room: all the parts of the apparatus may be the same as those in the fire alarum, except by having open tubes of mercury near doors and windows, instead of thermometers in each room. A third variety, the 'Railway Alarum,' is intended to establish signals of communication between the guard and the engine-driver of a railway train. There is a copper wire carried through or upon or beneath each carriage, and connected with another in the adjoining carriage by a flexible metallic cord: the wire and cord being coated with gutta percha to secure isolation. There is thus a wire communication from end to end of the train. The guard has in his box or seat, a very small galvanic battery; and the engine-driver has a series of small studs connected with the rail on which his hand is usually resting. When the guard wishes to communicate with the engine-driver, he sends a slight galvanic shock through the wire to the spot on which the hand of the driver rests; and the duplication or variation of the shock may be made to indicate various signals.-It must be evident that great completeness and exactness would be necessary to render any of the above three kinds of alarum efficient for the purpose intended; and it may be added that, as yet, the contrivances have not come into actual use.

A floating alarum was suggested a few years ago by Mr Hobbs, of Bristol, to be moored to a sunken rock or other dangerous place at sea. The centre of the machine is an air-vessel or buoy. At each end is a box in which a whistle is fixed, whose mouth is protected from the water. As the water of the sea circulates in certain parts of the interior of the machine, it drives the air alternately from one end to the other, and impels it through the whistles; and the more violently the sea rocks the floating machine, the louder will the whistles give forth their sound. The proposal of the inventor is to make the buoy and whistles of such dimensions that the sound may be heard some miles distant. [Buors.]

ALBATA, is the name given to one of the numerous varieties of white metal, now so largely used in many branches of manufacture at Birmingham. Different mixtures or alloys will produce a white metal. For example, Mr. Parker obtained in 1844 a patent for five such compounds, all having the properties of whiteness and considerable malleability. One consists of zinc, tin, iron, and copper, in certain specified proportions; another of zinc, tin, and antimony; a third of zinc, nickel, iron, and copper; a fourth of copper, nickel, and silver; and a fifth of nickel, iron, and copper. It seems evident from the specification, that many different proportions of the ingredients may be adopted, in each of the above kinds. The mode of making white metal, of zinc 50, tin 48, iron 1, and copper 3, is thus described :-the iron and copper are first melted together in a crucible, and while in a fused state, the tin is added in such quantities at a time that the iron and copper shall not become solid; the zinc is then added, and the whole well combined by stirring. The flux is composed of one part of lime, one part of Cumberland ore, and three parts of salammonia. The alloy thus produced may be cast in sand or ingots for rolling. The nickel-silver,' which has recently come largely into use, is a cheap substitute for silver, superior in many respects to albata, and having the metal nickel as one of its components.

[ocr errors]

See further in respect of these compound metals under ALLOY. ALBIGENSES, a religious sect, which appeared in the South of France in the twelfth century, and was the object of long and cruel persecutions and wars. The denomination of Albigenses has been used by historians and other writers in two senses, and often indiscriminately. In its more restricted and appropriate sense, the Albigenses were a branch of the Paulicians from the East, who, being persecuted by the Greek emperors and clergy, took refuge during the eleventh century in Italy, from whence they spread into the South of France, Spain, and other countries. They were called in Italy, Cathari, or pure;" also Paterini, from a place in Milan where they held their meetings; and Gazari, from Gazaria or Lesser Tartary, the country from which they came; they were called, in France, Bulgares, for a similar reason: and afterwards Albigenses, from Albiga, Albi, the town where their tenets were condemned by a council in 1176. But the Cathari were divided into two sects, one of which held the old Manichean doctrine of two eternal beings, one the God of Light, who was the Father of Jesus, and the other, the Principle of Darkness, who was the creator of the material world. This sect was also called Albanenses. The other division of the Cathari believed in one eternal principle, the Supreme God and Father of Christ, by whom the first matter was created; until the Evil Being, after his rebellion against God and his subsequent fall from heaven, arranged this original matter according to his own fancy, and gave it its present form and attributes. They believed that human bodies in particular were the production of the evil principle. The Albigenses belonged to this latter sect, which was also called Bajolenses or Bagnolenses. They had bishops, vicars, and deacons; they preached abstinence, mortification, and celibacy; their community, however, was divided into two classes, the Consolati, or "comforted," who lived in perpetual celibacy, abstained from meat and wine, and practised other austerities; and the Confederates, who, being unable to endure this mode of existence, lived apparently like the rest of the world, but bound themselves to enter before their death into the class of the "Comforted" by a ceremony of inauguration. But, in the more extended sense, the name of Albigenses was given in the twelfth and thirteenth centuries, not only to all the Cathari indiscriminately, but also to the other sects which existed in the South of France at the time, including the Waldenses, who were very distinct in their tenets from the others, and had no taint of Manicheism in them. They all agreed, however, in considering the authority assumed by the Popes in spiritual matters, as well as the discipline and ceremonies of the Roman Church, as unlawful and erroneous. Pope Innocent III. sent two legates, Peter of Castelnau, and one Rainier or Raoul, both Cistercian or Bernardine monks, as his legates to France, in order to extirpate all these heresies. Dominic, a Spaniard, and the founder of the order of Preachers, returning from Rome in 1206, fell in with the legates, and volunteered his services in the same cause. These champions, who, without asking for the advice or the concurrence of the local bishops, and upon the sole authority of the Pope, inflicted capital punishment on those heretics whom they could not convert by argument, were called, in common discourse, 'Inquisitors;' but the famous tribunal of that name was not established until 1233, by Gregory IX., who entrusted it to the Dominicans. In 1208, Castelnau, one of the legates, who had become odious by his severities, was murdered near Toulouse; and Innocent III. on this proclaimed a regular crusade against the Albigenses, and against Raymond VI., Count of Toulouse, who supported them. All the French barons were summoned to take the field; and Simon, Count of Montfort, was appointed chief of the expedition, under the direction, howof Arnald, Abbot of the Cistercians, and the Pope's new legate. The war began in 1209, and lasted many years, attended by circumstances of the greatest ferocity. At the taking of Béziers a general massacre of the inhabitants began. The legate being asked by some of the military leaders how they were to distinguish the Albigenses from the orthodox Catholics, of whom there were many in the town,"Kill them all," was the reply; "God will find out his own." Montfort lost his life at the siege of Toulouse, in 1218, and Raymond, his

ever,

[ocr errors]

adversary, died in 1222. The war, however, was resumed by the sons of the two antagonists; until Pope Honorius III., alarmed at the suc cesses of Raymond VII., induced Louis VIII., King of France, to take the field in person. At last the Count of Toulouse, pressed on all sides, made peace with the King in 1229. This was a mortal blow to the Albigenses. The Inquisition was now permanently established at Toulouse to try those heretics who had escaped the sword. Raymond himself died some years after; and in him the house of the Counts of Toulouse became extinct, and its territories reverted to the French crown. The extermination of the Albigenses in the South of France was complete; the country was devastated; and the language and poetry of the Troubadours became also extinct, the bards themselves being obliged by the terrors of the Inquisition to fly to other lands. Langlois, a Jesuit, has written a History of the Crusade against the Albigenses;' but a better account of them is found in the General History of Languedoc,' published at Paris in 1730.

[ocr errors]

AL BORAK, the name of an imaginary animal, on which, according to a Mohammedan tradition, considered as a dream by some, the Arabian prophet performed his journey from the temple at Jerusalem through the heavens. It is conceived by them to have been of a middle stature and size between that of a mule and of an ass, and to have received its name in allusion to the shining whiteness of its colour.

ALBUM, a Latin word, signifying any thing white. The prætor's album was probably a board, either having the surface or the letters white, on which the acts and edicts of that functionary were inscribed and publicly exhibited. The opinion of some writers, who have supposed that it was the room or place where such notices were hung up, is undoubtedly erroneous. Among the later Latin authors we read of the album of the judges, the album of the senators, and even the album of the citizens, which seem to have been books or registers in which the names of persons of those orders were enrolled. In the middle ages we find album, and albus, and albo (as an indeclinable noun), used for a register of saints, a muster-roll of soldiers, or, in general, any list or catalogue of names. Album also sometimes signifies a letter or epistle, in allusion to the white surface of the paper or parchment. (See the Glossaries' of Ducange and Carpentier.) An album, in modern times, is a book appropriated usually to receive the autographs or other manuscript contributions of authors, travellers, or any other person of whom it is thought worth while to collect such memorials; but sometimes, also, merely as a repository of drawings, prints, verses, and other miscellaneous fragments. On the Continent, the matriculation list and the black board at the universities have received this name; and the note-book of a tourist, in which he makes on the spot his memoranda of places and occurrences, is often called his album.

ALBUMEN. A member of the group of substances known as the albuminoid or protein group. There are albumen, represented by the white of egg and the serum of blood; fibrin-the muscular tissue of animals; casein-found in solution in milk, and forming the basis of cheese; and legumin, existing in the seeds of all leguminous plants. To these may be added globulin and vitellin.

The chemical composition of the varieties of the protein compounds is nearly identical, the ultimate analysis of albumen differing but slightly from that of the others. The following is by Mulder :

[blocks in formation]

Mulder considers that albumen, fibrin, and casein are compounds of fundamental principle-protein-with different proportions of phosphorus and sulphur. This substance, however, to which the formula CH,,N.O12 has been assigned, has never been obtained free from sulphur.

12

As the animal body is composed to a large extent of muscular and fibrous tissues (fibrin), so it is impossible for an animal to exist on food that contains no protein principle; and Liebig considers that such azotized matter in the food is assimilated directly in the process of digestion by the animal, constituting muscle, nerves, &c. The proteic are sometimes termed the plastic elements of nutrition, in distinction from the respiratory elements.

Albumen forms a constituent both of the animal fluids and solids. Of the animal fluids, it forms an essential part of the serum of the blood; it abounds in the fluid that moistens the surface of the internal cavities of the body and of the organs they contain, and it exists in large quantity in the watery fluid poured out into those cavities in the disease termed dropsy. In some diseases it is met with in the urine. In the animal solids it forms the principal part of all membranes; of the skin, of fibrin, the basis of muscle or flesh, and of the organs called glands.

Albumen then exists in the animal body in two states, in the fluid and the solid form. The best example of fluid albumen is the white of egg. The white of egg consists entirely of albumen held in solution

« السابقةمتابعة »